2-In-1 Stand
Assembly Instructions
Model: BDS1642
Parts
Tools Required
#
1
Qty. Description
7/32" Allen Wrench (included)
1
1
1
2
1
1
1
1
1
TUBE, BOTTOM CROSS BRACE
ASSEMBLY, REAR LEFT STABILIZER
ASSEMBLY, REAR RIGHT STABILIZER
ASSY, STAND LEG
2
3
You will also need:
4
9/16" Socket
9/16" Wrench or Adjustable Wrench
Utility knife or scissors to cut nylon ties
5
WELDMENT, LEFT DUMBBELL PLATFORM
WELDMENT, RIGHT DUMBBELL PLATFORM
WELDMENT, TOWEL BAR
6
7
8
FOOT PEGS, SET OF FOUR
9
HOLD DOWN STRAPS, 2F 2M
10
11
12
13
14
15
16
17
20 NUT-NL 0.375-16 G2-BlkZ
36 WASHER-FLAT 0.375 REGULAR BLKZ
8
4
4
4
1
1
SCREW-BHCS 0.375-16x3.0 G2-BlkO
SCREW-BHCS 0.375-16x2.75 G2-BlkO
SCREW-BHCS 0.375-16x2.5 G2-BlkO
SCREW-FHCS 0.375-16x1.0 G2-BlkO
WHEELS, CASTER SET OF FOUR
PLATE, CENTER W/ LOGO
Hardware
Qty
Hardware Card A:
3.0"
2.75" Screw, Button Head
2.5" Screw, Button Head
1.0" Screw, Flat Head
Nut, Lock
4
4
4
12
20
Button Head
2.75"
Washer, Flat
Button Head
Hardware Card B:
3.0" Screw, Button Head
Nut, Lock
2.5"
8
8
16
Button Head
Washer, Flat
7/32" Allen Wrench
Flat Head
Lock Nut
Flat Washer
3
step
1
�
�
��
��
��
��
Figure 1
Parts:
• Stand Leg (#4)
• Rear Left Stabilizer (#2)
Hardware
Qty
• 3" Screws (#12)
• Washers (#11)
• Nuts (#10)
2
4
2
Tools:
• Hex Key (7/32”)
1-1 Attach the Rear Left Stabilizer (#2) to the Stand Leg (#4) using the hardware shown in Figure 1.
Note: Do not tighten hardware.
4
step
2
�
��
��
�
��
��
Figure 2
Parts:
• Stand Leg (#4)
• Rear Right Stabilizer (#3)
Hardware
Qty
• 3" Screws (#12)
• Washers (#11)
• Nuts (#10)
2
4
2
Tools:
• Hex Key (7/32”)
2-1 Attach the Rear Right Stabilizer (#3) to the Stand Leg (#4) using the hardware shown in Figure 2.
Note: Do not tighten hardware.
5
step
3
�
�
��
�
��
��
�
�
Figure 3
Parts:
• Cross Brace (#1)
• Left Stand Leg assembly from Step 1
• Right Stand Leg assembly from Step 2
Hardware
Qty
• 3" Screws (#12)
• Washers (#11)
• Nuts (#10)
4
8
4
Tools:
• Hex Key (7/32”)
3-1 Attach the Bottom Cross Brace (#1) to the Rear Left Stabilizer (#2) and Rear Right Stabilizer (#3)
using the hardware shown in Figure 3. Make sure that the narrower edge of the Cross Brace
(#1) is closer to the Stand Leg (#4) uprights.
Note: Do not tighten hardware.
6
step
4
��
��
��
��
��
��
��
��
��
Figure 4
Parts:
• Stand Leg and Cross Brace assembly from Step 3
• Center Plate (#17)
Hardware
Qty
• 2.5" Screws (#14)
• Washers (#11)
• Nuts (#10)
4
8
4
Tools:
• Hex Key (7/32”)
• Wrench/Socket (9/16”) or Adjustable Wrench
4-1 Install the Center Plate (#17) to both Stand Legs (#4) using the hardware shown in Figure 4.
Note: Make sure that the Center Plate edges are on the outer sides of the legs, and that the logo
on the Plate is right side up.
4-2 Tighten all hardware from Steps 1, 2 and 3 securely.
7
step
5
�
��
��
��
��
Figure 5
Parts:
• Stand base assembly from Step 4
• Left Dumbbell Platform (#5)
Hardware
Qty
• 2.75" Screws (#13) 2
• Washers (#11)
• Nuts (#10)
4
2
Tools:
• Hex Key (7/32”)
• Wrench/Socket (9/16”) or Adjustable Wrench
5-1 Secure the Left Dumbbell Platform (#5) to left Stand Leg (#4) using the hardware shown in
Figure 5.
Note: Make sure the screw holes in the Platform are toward the center of the stand.
8
step
6
�
��
��
��
��
Figure 6
Parts:
• Stand base assembly from Step 5
• Right Dumbbell Platform (#6)
Hardware
Qty
• 2.75" Screws (#13) 2
• Washers (#11)
• Nuts (#10)
4
2
Tools:
• Hex Key (7/32”)
• Wrench/Socket (9/16”) or Adjustable Wrench
6-1 Secure the Right Dumbbell Platform (#6) to right Stand Leg (#4) using the hardware shown in
Figure 6.
Note: Make sure the screw holes in the Platform are toward the center of the stand.
9
step
7
�
��
��
��
��
��
��
Figure 7
Parts:
• Stand assembly from Step 6
• Towel Bar (#7)
Hardware
Qty
• 1" Screws (#15)
• Washers (#11)
• Nuts (#10)
4
4
4
Tools:
• Hex Key (7/32”)
• Wrench/Socket (9/16”) or Adjustable Wrench
7-1 Attach the Towel Bar (#7) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform
(#6) using hardware shown in Figure 7. Hand tighten screws in a cross pattern, to ensure
even fit.
7-2 Tighten all screws securely.
10
step
8
�
��
�
Figure 8
Parts:
• Stand assembly from Step 7
• Foot Pegs (#8) or Caster Wheels (#16)
• Hold Down Straps (#9)
8-1 Attach either Foot Pegs (#8) or Caster Wheels (#15) to the Rear Left Stabilizer (#2), the Rear
Right Stabilizer (#3), and both Stand Legs (#4). See Figure 8.
8-2 Attach the Hold Down Straps (#9) to the Left Dumbbell Platform (#5) and the Right Dumbbell
Platform (#6) as shown in Figure 8.
11
16400 SE Nautilus Dr.
Vancouver, Washington, USA 98683
© 2006 Nautilus, Inc. All Rights Reserved.
Bowflex and Bowflex SelectTech are either registered
trademarks or trademarks of Nautilus, Inc.
Specifications subject to change.
P/N 000-3708 RevB 02/06
|
Bernard Welder FLX3515AM User Manual
Blackberry Cell Phone 7100I User Manual
Black Box Electronic Accessory 2 Port USB 30 Fiber Extender User Manual
Black Box Network Cables CAT6 User Manual
Blue Rhino Charcoal Grill NBC3121D User Manual
Bogen Speaker CSUB User Manual
Briggs Stratton Portable Generator 30228 User Manual
Carrier Heating System 06 User Manual
Cecilware Coffeemaker FTC 3 N User Manual
Chamberlain Garage Door Opener 1145 1 3HP User Manual