Quickie ST/D T
User
Instruction
Manual &
Warranty
SUPPLIER:
THIS MANUAL MUST BE GIVEN TO THE RIDER OF THIS
WHEELCHAIR.
RIDER:
BEFORE USING THIS WHEELCHAIR READ THIS ENTIRE
MANUAL AND SAVE FOR FUTURE REFERENCE
I I . T A B L E O F C O N T E N T S
I I . T A B L E O F C O N T E N T S
i. Power Drive ........................................................................................ 17
j. Quick-Release Axles .......................................................................... 17
k. Rear Axles ............................................................................................ 17
l. Rear Wheel Locks .............................................................................. 17
m.Modified Seat Systems ...................................................................... 18
n. Upholstery Fabric .............................................................................. 18
VIII. TIPS FO R ATTENDANTS ............................................................ 19
a. Learning to do a “Wheelie” ............................................................ 19
b. Descending a Curb or Single Step .................................................. 19
c. Climbing a Curb or Single Step ...................................................... 20
d. Climbing Stairs .................................................................................... 20
e. Descending Stairs ................................................................................ 20
1. INTRO DUCTIO N ..............................................................................
a. Quickie Listens ......................................................................................
11. TABLE O F CO NTENTS ..................................................................
III. YO UR CHAIR AND ITS PARTS ................................................
1
1
2
4
IV. NOTICE - READ BEFO RE USE ..................................................
a. Choose the Right Chair & Safety Option ......................................
b. Review this Manual Often ................................................................
c.Warnings..................................................................................................
6
6
6
6
V. GENERAL WARNINGS....................................................................
a. Weight Limit ........................................................................................
b. Weight Training ....................................................................................
c. Getting to Know Your Chair ............................................................
d. To Reduce The Risk of an Accident ................................................
e. Safety Checklist ..................................................................................
f. Changes & Adjustments ....................................................................
g. Environmental Conditions ................................................................
h. Terrain ....................................................................................................
i. Street Use ............................................................................................
j. Motor Vehicle Safety ..........................................................................
k. When You Need Help ........................................................................
7
7
7
7
7
8
8
8
8
8
9
9
IX. CHAIR BASICS .................................................................................. 21
a. To Mount & Remove Rear Wheels ................................................ 21
X. SET-UP AND ADJUSTMENTS .................................................... 22
a.Wheels .................................................................................................... 22
b.Wheel Locks ........................................................................................ 22
c.Armrests (Optional) ............................................................................ 23
d.Anti-Tip Tubes (Optional) .................................................................. 23
e. Height Adjustable Armrest (Optional) .......................................... 24
f. Folding Backrest .................................................................................... 24
g. Back Angle Adjustable (Folding Backrest) ...................................... 24
h. Camber Tube ........................................................................................ 25
i.Wheel Locks .......................................................................................... 26
j. Footrest .................................................................................................. 27
k.Anti-Tip Tubes (Optional) .................................................................. 27
XI. TRO UBLESHO OTING .................................................................... 26
X11. MAINTENANCE ................................................................................ 27
XIII. Q UICKIE LIMITED WARRANTY .............................................. 29
VI. WARNINGS: FALLS & TIP-OVERS .......................................... 10
a. Center of Balance .............................................................................. 10
b. Dressing or Changing Clothes ........................................................ 10
c. Wheelies .............................................................................................. 11
d. Obstacles .............................................................................................. 11
e. Reaching or Leaning .......................................................................... 11
f. Moving Forward .................................................................................. 12
g. Ramps, Slopes & Side Hills ................................................................ 12
h. Transfers ................................................................................................ 13
i. Curbs & Steps ...................................................................................... 14
j. Stairs ...................................................................................................... 14
k. Escalators .............................................................................................. 14
VII. WARNINGS: CO MPO NENTS & O PTIO NS ........................ 15
a. Amputee or “Extended” Axle Plates .............................................. 15
b. Anti-Tip Tubes ...................................................................................... 15
c. Armrests .............................................................................................. 15
d. Cushion & Sling Seats ........................................................................ 15
e. Fasteners .............................................................................................. 16
f. Footrests ................................................................................................ 16
g. Pneumatic Tires .................................................................................. 16
h. Positioning Belts .................................................................................. 16
2
3
I I I . Y O U R
C H A I R A N
D
I T S P A R T S
I I I . Y O U R
C H A I R A N
D
I T S P A R T S
We igh t
Ca st e r s
22 lbs. with steel rear axles
20.5 lbs. with titanium rear axles and
performance wheels
Std - 5”, low-profile polyurethane
Opt - 3” micros, (may require differ-
ent forks, stems or spacers)
1
A d ju st m e n t s
A r m r e st s
Opt - height-adjustable
Camber Tubes
2
1” vertical caster adjustment with
2-hole fork
3
2” wheelbase width adjustment
o
o
o
o
o
o
o
0 , 3 , 6 , 9 , 12 , 15
6
seat angle adjustment
19
A x le s
Std - stainless steel
Opt - titanium, quad-release axle
nuts
Co lo r s
Blue, Black, Red, Midnight Purple,Teal
Pearl Pink, Lavender, Forest Green
Burgundy,Yellow, Blue Green, Candy
Teal, Candy Razzberry, Candy Purple
St a n d a r d Re a r Wh e e ls
Std - spoke
Opt - mountain
13
12
11
Ch a ir Pa r t s
Std - Black
Qu ick ie Pe r fo r m a n ce Wh e e ls
Opt - tennis, basketball, heat-treated
tennis, heat-treated basketball
6
Fr a m e Dim e n sio n s
Frame width: Std - 12”-20”
Sling depth: 12”-19”
10
Cushion: 2”, 3”, 4”
5
Tir e Siz e
Std - 24”
Opt - 22”, 26”
9
14
15
Ba ck r e st
Folding - adjustable height: 11”-14”,
15”-18”
Backrest options: push handles,
adjustable upholstery
7
8
All features may not be available with
some chair set-ups or in conjunction
with another chair feature. Please
consult your Quickie Sports Center
for more information.
Q uickie Shadow ST/DT
1. Backrest
9. Spokes
Fo o t r e st s
2. Pneumatic tire
3. Seat cushion
10. Rear wheel hub
11. Quick-release axle
12. Aluminum wheel rim
13. Caster housing
14. Caster fork
Std - Rigid (Shadow ST)
Std - Platform (Shadow DT)
Opt - Adaptive, adjustable
Impact guards - neoprene
4. Seat sling (not shown)
5. Scissor wheel lock
6. Leg strap
7. Footrest
15. Caster wheel
8. Aluminum handrim
4
5
I V .
N
O T I C E — R E A D B E F O R E U S E
!
V . G E N E R A L W A R N I N G S
L
A . CH OOSE TH E RIGH T CH A IR & SA FETY OPTION S
Quickie provides a choice of many wheelchair styles to meet the needs of the
wheelchair rider. However, final selection of the type of wheelchair, options
and adjustments rests solely with you and your health care advisor. Choosing
the best chair and set-up for your safety depends on such things as:
1. Your disability, strength, balance and coordination.
W A R N I N G S
!
L
Heed all warnings in this section. If you fail to do so a fall, tip-over or loss
of control m ay occur and cause severe injury to the rider or others.
A . WEIGH T LIMIT
NEVER exceed the weight limit of 250 pounds (113.6 kilogram s) for
combined weight of rider and items carried. This may cause the chair to fail.
2. The types of hazards you must overcome in daily use (where you live and
work, and other places you are likely to use your chair).
3. The need for options for your safety and comfort (such as anti-tip tubes,
positioning belts, or special seating systems).
B. WEIGH T TRA IN IN G
NEVER use this chair for weight training if total weight (rider plus equipment)
exceeds 250 pounds. This is likely to damage seat, frame and fasteners and will
void the warranty.
B. REVIEW TH IS MA N UA L OFTEN
Before using this chair you, and each person who may assist you, should read
this entire manual and make sure to follow all instructions. Review the warn-
ings often, until they are second nature to you.
C. GETTIN G TO KN OW YOUR CH A IR
Every wheelchair is different. Take the time to learn the feel of this chair
before you begin riding. Start slowly, with easy, smooth strokes. If you are
used to a different chair, you may use too much force and tip over.
C. WA RN IN GS
The word "WARNING" refers to a hazard or unsafe practice that may cause
severe injury or death to you or to other persons. The "Warnings" are in
three main sections, as follows:
D. TO REDUCE TH E RISK OF A N ACCIDEN T
1. BEFORE riding, you should be trained in the safe use of this chair by your
health care advisor.
1. V — GENERAL WARNINGS
2. Practice bending, reaching and transfers until you know the limit of your
ability. Have someone help you until you know what can cause a fall or
tip-over and how to avoid doing so.
Here you will find a safety checklist and a summary of risks you need to be
aware of before you ride this chair.
2. VI — WARNINGS — FALLS & TIP-OVERS
Here you will learn how to avoid a fall or tip-over while you perform daily
activities in your chair.
3. Be aware that you must develop your own methods for safe use best
suited to your level of function and ability.
4. NEVER try a new maneuver on your own until you are sure you can do it
safely.
5. Get to know the areas where you plan to use your chair. Look for hazards
and learn how to avoid them.
6. Use anti-tip tubes unless you are a skilled rider of this chair and are sure
you are not at risk to tip over.
3. VII — WARNINGS — CO MPO NENTS & O PTIO NS
Here you will learn about the components of your chair and options you can
select for safety. Consult your authorized Quickie supplier and your health
care advisor to help you choose the best set-up and options for
safe use.
Note: Where they apply, you will also find "Warnings" in other sections of this Manual.
E. SA FETY CH ECKLIST
Before Each Use Of Your Chair:
1. Make sure the chair rolls easily and that all parts work smoothly. Check
for noise, vibration, or a change in ease of use. (They may indicate low tire
pressure, loose fasteners, or damage to your chair.)
2. Repair any problem. Your authorized Quickie supplier can help you find
and correct the problem.
3. Check to see that both quick-release rear axles are locked. When locked,
the axle button will "pop out" fully. (See p. 21) If not locked, the wheel
may come off and cause you to fall.
4. If your chair has anti-tip tubes, lock them in place.
Note: See p. 21 for times you should not use them.
6
7
!
!
V . G E N E R A L W A R N I N G S
V . G E N E R A L W A R N I N G S
L
L
F. CH A N GES & A DJUSTMEN TS
3. NEVER transport this chair in the front seat of a vehicle. It may shift and
interfere with the driver.
4. ALWAYS secure this chair so that it cannot roll or shift.
If you modify or adjust this chair, it may increase the risk of a tip-over UNLESS
you make other changes as well.
1. Consult your authorized Quickie supplier BEFORE you modify or adjust
your chair.
2. We recommend that you use anti-tip tubes until you adapt to the change,
and are sure you are not at risk to tip over.
K. WH EN YOU N EED H ELP
For The Rider :
Make sure that each person who helps you reads and follows all warnings and
instructions that apply.
For Attendants:
G. EN VIRON MEN TA L CON DITION S
1. Work with the rider's doctor, nurse or therapist to learn safe methods best
suited to your abilities and those of the rider.
1. Use extra care if you must ride your chair on a wet or slick surface. If you
are in doubt, ask for help.
2. Tell the rider what you plan to do, and explain what you expect the rider to
do. This will put the rider at ease and reduce the risk of an accident.
3. Make sure the chair has push handles. They provide secure points for you
to hold the rear of the chair to prevent a fall or tip-over.
•Check to make sure push handle grips will not rotate or slip off.
4. To prevent injury to your back, use good posture and proper body mecha-
nics. When you lift or support the rider or tilt the chair, bend your knees
slightly and keep your back as upright and straight as you can.
5.Rem ind the rider to lean back when you tilt the chair backward.
6. W hen you descend a curb or single step, slowly lower the chair
in one easy m ovem ent.
2. Contact with water or excess moisture may cause your chair to rust or
corrode. This could cause your chair to fail.
a. Do not use your chair in a shower, pool or other body of water. The
chair tubing and parts are not water-tight and may rust or corrode from
the inside.
b. Avoid excess moisture (for example, do not leave your chair in a damp
bathroom while taking a shower).
c. Dry your chair as soon as you can if it gets wet, or if you use water to
clean it.
H . TERRA IN
1. Your chair is designed for use on firm, even surfaces such as concrete,
asphalt and indoor floors and carpeting.
• Do not let the chair drop the last few inches to the ground.
This m ay dam age the chair or injure the rider.
2. Do not operate your chair in sand, loose soil or over rough terrain.
This may damage wheels or axles, or loosen fasteners of your chair.
7. To avoid tripping, unlock and rotate anti-tip tubes up, out of the way.
8. ALWAYS lock the rear wheels and lock anti-tip tubes in place if you must
leave the rider alone, even for a moment. This will reduce the risk of a tip
over or loss of control of the chair.
I. STREET USE
In most states, wheelchairs are not legal for use on public roads. Be alert
to the danger of motor vehicles on roads or in parking lots.
1. At night, or when lighting is poor, use reflective tape on your chair and
clothing.
2. Due to your low position, it may be hard for drivers to see you. Make eye
contact with drivers before you go forward. When in doubt, yield until you
are sure it is safe.
J. MOTOR VEH ICLE SA FETY
Quickie wheelchairs do not meet federal standards for motor vehicle seating.
1. NEVER let anyone sit in this chair while in a moving vehicle.
a. ALWAYS move the rider to an approved vehicle seat.
b. ALWAYS secure the rider with proper motor vehicle restraints.
2. In an accident or sudden stop the rider may be thrown from the chair.
Wheelchair seat belts will not prevent this, and further injury may result
from the belts or straps.
8
9
!
!
V I . W A R N I N G S : F A L L S
&
T I P - O V E R S
V I . W A R N I N G S : F A L L S
&
T I P - O V E R S
L
L
C. WH EELIES
W A R N I N G S
!
L
Doing a "wheelie" means: balancing on the rear wheels of your chair, while the
front casters are in the air. It is dangerous to do a "wheelie" as a fall or tip-
over may occur. However, if you do it safely, a "wheelie" can help you over-
come curbs and obstacles.
Heed all warnings in this section. If you fail to do so a fall, tip-over or loss
of control m ay occur and cause severe injury to the rider or others.
A . CEN TER OF BA LA N CE
1. Consult your doctor, nurse or therapist to find out if you are a good candi-
date to learn to do a "wheelie."
2. Do not attempt a "wheelie" UNLESS you are a skilled rider of this chair, or
you have help.
The point where this chair will tip forward, back, or to the side depends on
its center of balance and stability. How your chair is set up, the options you
select and the changes you make, may affect the risk of a fall or tip-over.
1. The Most Im portant Adjustm ents Are:
Note: See p. 19 for steps to learn to do a "wheelie."
a. The position of the rear axles. The more you move the axles forward, the
more likely your chair will tip over backward.
D. OBSTACLES
b. The position of the front casters. Moving the casters back (or "reversing"
them) will increase the risk of tipping forward.
2. The Center O f Balance Is Also Affected By:
a. A change in the set-up of your chair, including:
• The distance between the rear wheels.
Obstacles and road hazards (such as potholes and broken pavement) can damage
your chair and may cause a fall, tip-over or loss of control. To avoid these risks:
1. Keep a lookout for danger — scan the area well ahead of your chair as
you ride.
2. Make sure the floor areas where you live and work are level and free of
obstacles.
• The amount of rear wheel camber.
• The seat height and seat angle.
b. A change in your body position, posture or weight distribution.
c. Riding your chair on a ramp or slope.
3. Remove or cover threshold strips between rooms.
4. Install a ramp at entry or exit doors. Make sure there is not a drop off
at the bottom of the ramp. (See p. 12)
d. The use of a back pack or other options, and the amount of added weight.
3. To Reduce The Risk O f An Accident:
5. To Help Correct Your Center Of Balance:
a. Lean your upper body FORWARD slightly as you go UP over an
obstacle.
b. Press your upper body BACKWARD as you go DOWN from a higher
to a lower level.
6. If your chair has anti-tip tubes, lock them in place before you go UP over
an obstacle.
a. Consult your doctor, nurse or therapist to find out what axle and caster
position is best for you.
b. Consult your authorized Quickie supplier BEFORE you modify or adjust
this chair. Be aware that you may need to make other changes to correct
the center of balance.
c. Have someone help you until you know the balance points of your chair
and how to avoid a tip-over.
d. Use anti-tip tubes.
7. Keep both of your hands on the handrims as you go over an obstacle.
8. Never push or pull on an object (such as furniture or a doorjamb) to
propel your chair.
E. REACH IN G OR LEA N IN G
B. DRESSIN G OR CH A N GIN G CLOTH ES
If you reach or lean it will affect the center of balance of your chair. This may
cause you to fall or tip over. When in doubt, ask for help or use a device to
extend your reach.
1. NEVER reach or lean if you must shift your weight sideways or rise up off
the seat.
Your weight may shift if you dress or change clothes while seated in this chair.
To reduce the risk of a fall or tip-over:
1. Rotate the front casters until they are as far forward as possible. This
makes the chair more stable. (See p. 27)
2. Lock anti-tip tubes in place. (If your chair does not have anti-tip tubes,
back it up against a wall and lock both rear wheels.)
2. NEVER reach or lean if you must move forward in your seat to do so.
Always keep your buttocks in contact with the backrest.
10
11
V I . W A R N I N G S : F A L L S
&
T I P - O V E R S
!
!
V I . W A R N I N G S : F A L L S
&
T I P - O V E R S
L
L
6. NEVER use rear wheel locks to try to slow or stop your chair. This is like-
ly to cause your chair to veer out of control.
3. NEVER reach with both hands (you may not be able to catch yourself to
prevent a fall if the chair tips).
7. Beware Of:
4. NEVER REACH OR LEAN TO THE REAR unless your chair has anti-tip
tubes locked in place.
a. Wet or slippery surfaces.
b. A change in grade on a slope (or a lip, bump or depression). These may
cause a fall or tip-over.
c. A drop-off at the bottom of a slope. A drop-off of as small as 3/4 inch
can stop a front caster and cause the chair to tip forward.
8. To Reduce The Risk Of A Fall Or Tip-Over:
5. DO NOT REACH OR LEAN OVER THE TOP OF THE SEAT BACK. This
may damage one or both backrest tubes and cause you to fall.
6. If You Must Reach Or Lean:
a. Do not lock the rear wheels. This creates a tip point and makes a fall
or tip-over more likely.
a. Lean or press your body UPHILL. This will help adjust for the change in
the center of balance caused by the slope or side hill.
b. Keep pressure on the handrims to control your speed on a down slope.
If you go too fast you may lose control.
b. Do not put pressure on the footrests.
Note: Leaning forward puts pressure on the footrests and may cause the chair to tip if
you lean too far.
c. Move your chair as close as you can to the object you wish to reach.
d. Do not try to pick up an object from the floor by reaching down
between your knees. You are less likely to tip if you reach to the side
of your chair.
e. Rotate the front casters until they are as far forward as possible. This
makes the chair more stable. Note: To do this: Move your chair past
the object you want to reach, then back up alongside it. Backing up will
rotate the casters forward.
c. Ask for help any time you are in doubt.
9. Ram ps At Hom e & Work
For your safety, ramps at home and work must meet all legal requirements
for your area.We recommend:
a. Width. At least four feet wide.
b. Guardrails. To reduce the risk of a fall, sides of ramp must have
guardrails (or raised borders at least three inches high).
c. Slope. Not more than a 10% grade. (See p. 12)
d. Surface. Flat and even, with a thin carpet or other non-skid material.
(Make sure there is no lip, bump or depression.)
e. Bracing. Ramp must be STURDY. You may need bracing so ramp does
not "bow" when you ride on it.
f. Firmly grasp a rear wheel or an armrest with one hand. This will help
to prevent a fall if the chair tips.
F. MOVIN G BACKWA RD
Use extra care when you move your chair backward. You may lose control or
tip over if one of the rear wheels hits an object and stops rolling.
1. Propel your chair slowly and smoothly.
f. Avoid A Drop Off. You may need a section at the top or bottom to
smooth out the transition.
2. If your chair has anti-tip tubes, make sure to lock them in place.
3. Stop often and check to be sure your path is clear.
H . TRA N SFERS
It is dangerous to transfer on your own. It requires good balance and agility.
Be aware that there is a point during every transfer when the wheelchair seat
G. RA MPS, SLOPES & SIDE H ILLS
is not below you.
To Avoid A Fall:
1. Work with your health care advisor to learn safe methods.
RIDING ON A SLOPE, WHICH INCLUDES A RAMP OR SIDE HILL, will
change the center of balance of your chair. Your chair is less stable when it is
at an angle. Anti-tip tubes may not prevent a fall or tip-over.
1. Do not use your chair on a slope steeper than 10%. (A 10% slope means:
one foot in elevation for every ten feet of slope length.)
a. Learn how to position your body and how to support yourself during
a transfer.
b. Have someone help you until you know how to do a safe transfer on
2. Always go as straight up and as straight down as you can. (Do not "cut the
corner" on a slope or ramp.)
your own.
2. Lock the rear wheels before you transfer. This keeps the rear wheels
from rolling.
3. Do not turn or change direction on a slope.
4. ALWAYS STAY IN THE CENTER OF THE RAMP. Make sure ramp is wide
enough that you are not at risk that a wheel may fall over the edge.
5. Do not stop on a steep slope. If you stop, you may lose control of your chair.
Note: This will NOT keep your chair from sliding away from you or tipping.
12
13
!
!
V I . W A R N I N G S : F A L L S
&
T I P - O V E R S
V I . W A R N I N G S : F A L L S
&
T I P - O V E R S
L
L
3. Make sure to keep pneumatic tires properly inflated. Low tire pressure
may allow the rear wheel locks to slip.
4. Move your chair as close as as you can to the seat you are transferring to.
If possible, use a transfer board.
W A R N I N G S
!
L
Heed all warnings in this section. If you fail to do so a fall, tip-over or loss
of control m ay occur and cause severe injury to the rider or others.
5. Rotate the front casters until they are as far forward as possible.
(See p. 27)
Note: If you modify this chair or use parts not approved by Quickie, it may void
the warranty and create a safety hazard.
6. If you can, remove or swing footrests out of the way.
a. Make sure your feet do not catch in the space between the footrests.
b. Avoid putting weight on the footrests as this may cause the chair to tip.
7. Make sure armrests are out of the way and do not interfere.
8. Transfer as far back onto the seat surface as you can. This will reduce the
risk that the chair will tip or move away from you.
A . A MPUTEE OR "EX TEN DED" A X LE PLATES (O ptional)
Use extended axle plates for amputees or for persons with short leg length
or minimal leg mass. They allow you to set the rear axles farther back. This
adjusts the center of balance and will reduce the risk of a fall or tip-over.
B. A N TI-TIP TUBES (O ptional)
I. CURBS & STEPS
Anti-tip tubes can help keep your chair from tipping over backward in most
normal conditions.
1. Q uickie Recom m ends Use O f Anti-Tip Tubes:
a. UNLESS you are a skilled rider of this chair and are sure you are not at
risk to tip over.
1. Each person who helps you should read and follow the warnings "For
Attendants" (p. 19), and the "Tips For Attendants" (p. 9).
2. Do not try to climb or descend a curb or step alone UNLESS you are a
skilled rider of this chair and:
a. You can safely do a "wheelie"; and
b. Each time you modify or adjust your chair. The change may make it easier
to tip backward. Use anti-tip tubes until you adapt to the change, and are
sure you are not at risk to tip over.
b. You are sure you have the strength and balance to do so.
3. Unlock and rotate anti-tip tubes up, out of the way, so they do not interfere.
4. Do not try to climb a high curb or step (more than 4 inches high) UNLESS
you have help. Doing so may cause your chair to exceed its balance point
and tip over.
5. Go straight up and straight down a curb or step. If you climb or descend
at an angle, a fall or tip-over is likely.
6. Be aware that the impact of dropping down from a curb or step can dam-
age your chair or loosen fasteners.
2. When locked in place (in the "down" position) anti-tip tubes should be
BETWEEN 1 1/2 to 2 inches off the ground.
a. If set too HIGH, they may not prevent a tip-over.
b. If set too LOW, they may "hang up" on obstacles you can expect in normal
use. If this occurs, you may fall or your chair may tip over.
3. Keep Anti-Tip Tubes Locked In Place UNLESS:
a. You have an attendant; or
b. You have to climb or descend a curb, or overcome an obstacle, and can
safely do so without them.
J. STA IRS
1. NEVER use this chair on stairs UNLESS you have someone to help you.
Doing so is likely to cause a fall or tip-over.
At these times, make sure anti-tip tubes are up, out of the way.
2. Persons who help you should read and follow the warnings "For
Attendants" (p. 19), and the "Tips For Attendants" (p. 9).
C. A RMRESTS
Armrests detach and will not bear the weight of this chair.
1. NEVER lift this chair by its armrests. They may come loose or break.
2. Lift this chair only by non-detachable parts of the main frame.
K. ESCA LATORS
NEVER use this chair on an escalator, even with an attendant. If you do, a fall
or tip-over is likely.
Note: If you modify this chair or use parts not approved by Quickie, it may void the
warranty and create a safety hazard.
D. CUSH ION S & SLIN G SEATS
1. Quickie sling seats and standard foam cushions are not designed for the
relief of pressure.
2. If you suffer from pressure sores, or if you are at risk that they will occur,
you may need a special seat system or a device to control your posture.
•
Consult your doctor, nurse or therapist to find out if you need such a
device for your well-being.
14
15
!
V I . W A R N I N G S : F A L L S
&
T I P - O V E R S
V I . W A R N I N G S : F A L L S
&
T I P - O V E R S
!
L
L
E. FA STEN ERS
4. Use positioning belts only with a rider who can cooperate. Make sure
the rider can easily remove the belts in an emergency.
5. NEVER Use Positioning Belts:
Many of the screws, bolts and nuts on this chair are special high-strength fas-
teners. Use of improper fasteners may cause your chair to fail.
1. ONLY use fasteners provided by an authorized Quickie supplier (or ones
of the same type and strength, as indicated by the markings on the heads).
2. Over- or under-tightened fasteners may fail or cause damage to chair parts.
3. If bolts or screws become loose, tighten them as soon as you can.
a. As a patient restraint. A restraint requires a doctor's order.
b. On a rider who is comatose or agitated.
c. As a motor vehicle restraint. In an accident or sudden stop the rider
may be thrown from the chair. Wheelchair seat belts will not prevent
this, and further injury may result from the belts or straps.
F. FOOTRESTS
1. At the lowest point, footrests should be AT LEAST 21/2” off the ground.
If set too LOW, they may "hang up" on obstacles you can expect to find in
normal use. This may cause the chair to stop suddenly and tip forward.
2. To Avoid A Trip O r Fall W hen You Transfer :
a. Make sure your feet do not "hang up" or get caught in the space
between the footrests.
b. Avoid putting weight on the footrests, as the chair may tip forward.
c. Remove or swing the footrests out of the way, if possible.
3. NEVER lift this chair by the footrests. Footrests detach and will not bear
the weight of this chair. Lift this chair only by non-detachable parts of the
main frame.
I. POWER DRIVE
Do not install a power drive on any Quickie wheelchair. If you do:
1. It will affect the center of balance of your chair and may cause a fall
or tip-over.
2. It will alter the frame and void the warranty.
J. QUICK-RELEA SE A X LES
1. Do not use this chair UNLESS you are sure that both quick-release rear
axles are locked. An unlocked axle may come off during use and cause a fall.
2. An axle is not locked until the quick-release button pops out fully. and the
ball bearings are fully visible on the outside of the sleeve. (See p. 22)
K. REA R A X LES
G. PN EUMATIC TIRES
A change in set-up of the rear axles will affect the center of balance of your
chair.
Proper inflation extends the life of your tires and makes your chair easier
to use.
1. The farther you move the rear axles FORWARD, the more likely it is that
your chair will tip over backward.
2. Consult your doctor, nurse or therapist to find the best rear axle set-up
for your chair. Do not change the set-up UNLESS you are sure you are
not at risk to tip over.
1. Do not use this chair if any of the tires is under- or over-inflated. Check
weekly for proper inflation level, as listed on the tire sidewall.
2. Low pressure in a rear tire may cause the wheel lock on that side to slip
and allow the wheel to turn when you do not expect it.
3. Low pressure in any of the tires may cause the chair to veer to one side
and result in a loss of control.
3. Adjust the rear wheel locks after you make any change to the rear axles.
a. If you fail to do so, the locks may not work.
4. Over-inflated tires may burst.
b. Make sure lock arms embed in tires at least 3/8 inch when locked.
H . POSITION IN G BELTS (O ptional)
L. REA R WH EEL LOCKS
Use positioning belts ONLY to help support the rider's posture. Improper
use of these belts may cause severe injury to or death of the rider.
1. Make sure the rider does not slide down in the wheelchair seat. If this
occurs, the rider may suffer chest compression or suffocate due to pres-
sure from the belts.
2. The belts must be snug, but must not be so tight that they interfere with
breathing. You should be able to slide your open hand, flat, between the
belt and the rider.
Rear wheel locks are NOT designed to slow or stop a moving wheelchair.
Use them only to keep the rear wheels from rolling when your chair is at a
complete stop.
1. NEVER use rear wheel locks to try to slow or stop your chair when it is
moving. Doing so may cause you to veer out of control.
2. To keep the rear wheels from rolling, always set both rear wheel locks
when you transfer to or from your chair.
3. Low pressure in a rear tire may cause the wheel lock on that side to slip
and may allow the wheel to turn when you do not expect it.
4. Make sure lock arms embed in tires at least 3/8 inch when locked. If you
fail to do so, the locks may not work.
3. A pelvic wedge or a similar device can help keep the rider from sliding
down in the seat. Consult with the rider's doctor, nurse or therapist to
find out if the rider needs such a device.
16
17
!
V I . W A R N I N G S : F A L L S
&
T I P - O V E R S
V I I . T I P S F O R A T T E N D A N T S
L
M. MODIFIED SEAT SYSTEMS
W A R N I N G S
!
L
Use of a seat system not approved by Quickie may alter the center of balance
of this chair. This may cause the chair to tip over.
1. Do not change the seat system of your chair UNLESS you consult your
authorized Quickie supplier first.
Before you assist a rider, be sure to read the warnings “FO R ATTENDANTS”
(pg. 8) and follow all instructions that apply. Be aware that you will need to
learn safe m ethods best suited to your abilities.
2. Use of a seat system not approved by Quickie may affect the folding mech-
anism of this chair.
A . LEA RN IN G TO DO A "WH EELIE"
Follow these steps to help the rider learn to do a "wheelie":
1. Read and follow the warnings for "WHEELIES." (See p. 11)
2. Stand at the rear of the chair. You must be able to move with the chair to
prevent a tip-over.
3. Keep your hands BENEATH the push handles, ready to catch the rider if
the chair tips too far back.
4. When you are ready, have the rider place his or her hands on the forward
part of the handrims.
5. Have the rider make a quick BACKWARD movement of the rear wheels,
quickly followed by a hard FORWARD thrust. (This will tilt the chair up
on the balance point of the rear wheels.)
N . UPH OLSTERY FA BRIC
1. Replace worn or torn fabric of seat sling and seat back as soon as you can.
If you fail to do so, the seat may fail.
2. Sling fabric will weaken with age and use. Look for fraying or thin spots, or
stretching of fabric at rivet holes.
3. "Dropping down" into your chair will weaken fabric and result in the need
to inspect and replace sling more often.
4. Be aware that laundering or excess moisture will reduce flame retarda-
tion of the fabric.
6. Have the rider make small movements of the handrims to stay in balance.
B. DESCEN DIN G A CURB OR SIN GLE STEP
Follow these steps to help a rider descend a curb or single step going
BACKWARD:
1. Stay at the rear of the chair.
2. Several feet before your reach the edge of the curb or step, turn the chair
around and pull it backward.
3. While looking over your shoulder, carefully step back until you are off the
curb or stair and standing on the lower level.
4. Pull the chair toward you until the rear wheels reach the edge of the curb
or step. Then allow the rear wheels to slowly roll down onto the lower
level.
5. When the rear wheels are safely on the lower level, tilt the chair back to
its balance point. This will lift the front casters off the curb or step.
6. Keep the chair in balance and take small steps backward. Turn the chair
around and gently lower front casters to the ground.
18
19
V I I . T I P S F O R A T T E N D A N T S
V I I I . C H A I R
B A S I C S
C. CLIMBIN G A CURB OR SIN GLE STEP
Follow these steps to help the rider climb a curb or single step going
FORWARD:
A . TO MOUN T & REMOVE REA R WH EELS
W A R N I N G !
!
L
1. Stay behind the chair.
2. Face the curb and tilt the chair up on the rear wheels so that the front
casters clear the curb or step.
Do not use this chair UNLESS you are sure both quick-release axles are
locked. An unlocked axle m ay com e off during use and cause a fall.
3. Move forward, placing the front casters on the upper level as soon as you
are sure they are past the edge.
4. Continue forward until the rear wheels contact the face of the curb or
step. Lift and roll the rear wheels to the upper level.
Note: Axle is not locked until:
a. The quick-release button pops out
fully. (Fig.A)
b. The ball bearings are fully visible on
the outside of the sleeve. (Fig.A)
1. To Install W heel:
D. CLIMBIN G STA IRS
Note: Use at least two attendants to move a chair and rider up stairs.
1. Move the chair and rider BACKWARD up the stairs.
2. The person at the rear is in control. He or she tilts the chair back to its
balance point.
3. A second attendant at the front firmly grasps a non-detachable part of
the front frame and lifts the chair up and over one stair at a time.
4. The attendants move to the next stair up. Repeat for each stair, until you
reach the landing.
a. Depress quick-release button (1) fully.
This will release tension on ball bear-
ings at other end.
b. Insert axle through hub of rear wheel.
c. Keep pressure on button (1) as you
slide axle (2) into axle sleeve (3).
d. Release button to lock axle in sleeve.
Adjust axle if it does not lock.
(Follow steps at p. 22)
1. Quick-release
Figure A
E. DESCEN DIN G STA IRS
Note: Use at least two attendants to move a chair and rider down stairs.
1. Move the chair and rider FORWARD down the stairs.
2. The person at the rear is in control. He or she tilts the chair to the
balance point of the rear wheels and rolls it to the edge of the top step.
3. A second attendant stands on the third step from the top and grasps the
chair frame. He or she lowers the chair one step at a time by letting the
rear wheels roll over the stair edge.
e. Repeat steps on other side.
2. To Rem ove W heel:
a. Depress quick-release button (1) fully.
b. Remove wheel by sliding axle out of
axle sleeve (2).
2
3
c. Repeat steps on other side.
4. The attendants move to the next stair down. Repeat for each stair, until
you reach the landing.
20
21
I X
.
S E T U P
&
A D J U S T M E N
T
I X
.
S E T U P
&
A D J U S T M E N
T
Note: The Shadow ST/DT is shipped fully assem-
bled except for the following items which may
C. A RMRESTS (Op t io n a l)
To install armrest, slide the outer armpost
into the receiver that is mounted to the
wheelchair frame. The armrest will auto-
matically lock into place.
need to be attached or adjusted before final adjust-
ments are made. Setting the chair on a flat surface
(such as a workbench or table) helps make these
procedures easier.
Outer
Armpost
Note on Torque Setting: Unless otherwise, use
a torque setting of 60 in./lbs. when assembling this
wheelchair.
Note: Armrests can be mounted facing forward or
backward.
Armrests are detachable. Lifting the
wheelchair by them may cause damage to
the chair or injury to the rider. NEVER
lift the wheelchair by the armrests.
A . WH EELS
Depress the quick-release button on the axle
and slide it into the axle sleeve until it locks.
Receiver
W A R N I N G S
!
L
D. A N TI-TIP TUBES (Op t io n a l)
The axle is not secure until the outside
quick-release button pops out to its fully
extended position. Check to m ake sure
the axles are locked.
Insert anti-tip tube into anti-tip tube receiv-
er and placing locking pin through holes.
Note: Use a torque setting of 100 in./lbs. when
B. WH EEL LOCKS
assembling wheel locks.
Shadow ST/DT wheelchairs are shipped
with wheel locks mounted. Wheel locks
are installed at the factory unless you
have requested otherwise.
CAUTION:To allow the anti-tip tubes to
function properly there must be a 1 1/2” to
2” clearance from the anti-tip wheel to the
ground.
Note on Torque Setting: Use a torque setting of
W A R N I N G S
!
L
100 in./lbs. when assembling wheel locks.
Failure to adjust anti-tip tubes correctly
can result in injury to rider. Anti-tip tubes
are available from your local authorized
Q uickie supplier. Q uickie Designs recom -
m ends anti-tip tubes for wheelchairs.
Low-Mount Scissor W heel Locks:
The wheel lock mounts on a split-clamp
system. Loosen the bolts on the two
inside clamps. Position wheel lock on
frame tube and tighten bolts.
Note on Torque Setting: Unless otherwise
noted, use a torque setting of 60 in./lbs. when
assembling this wheelchair.
High-Mount Push-to-Lock or Scissor
W heel Locks:
The wheel lock mounts on a split-clamp
system. Loosen the bolts on the two
inside clamps. Position wheel lock on
frame tube and tighten bolts.
W A R N I N G S
!
L
Using wheel locks for braking is dangerous.
Use wheel locks for parking O NLY. W hen
properly adjusted, wheel locks prevent the
rear wheels from turning when the chair
is parked. Always adjust the wheel locks
after m aking any changes to the rear cam -
ber tube position. W heel locks should be
em bedded into the tires to prevent wheel
m ovem ent (when in the locked position).
22
23
I X
.
S E T U P
&
A D J U S T M E N
T
I X
.
S E T U P
&
A D J U S T M E N
T
E. H EIGH T-A DJUSTA BLE A RM-
REST (Op t io n a l)
H . CA MBER TUBE
The most important adjustment on your
2
a. Height-Adjustment
Shadow Rigid wheelchair is the position of
the camber tube. the center of gravity is
determined by the camber tube. The cen-
ter of gravity is determined by the camber
tube adjustment. Use a torque setting of
100 in./lbs. when adjusting rear axle.
To adjust armrest height, depress
detent button in the upright tube and
move up or down to the height
desired. Release button into proper
hole.
3
b. Removing Armrest
W A R N I N G S
!
L
To detach armrest, pull straight up on
armrest and remove.
1
Work with your health care professional for
assistance in adjusting the axle to a position
that is best suited to your abilities.
Height-Adjustable Arm rest
Key
1. Standard receiver
2.Armrest
W A R N I N G S
!
L
Arm rests are detachable. Lifting the
wheelchair by them m ay cause dam age
to the chair or injury to the rider.
1. Center of Gravity
The center of gravity is adjusted by mov-
ing the camber tube forward or backward
on the frame. Moving the axle forward
will increase your turning speed and light-
en the front end.
3. Receiver adjustment bolts
NEVER lift the wheelchair by the arm rests.
F. FOLDIN G BACKREST
The backrest comes standard with a 3”
height adjustment. Remove the backrest
upholstery from the frame. You will see
the backrest frame which telescopes into
the support and is secured by a screw on
the side of the frame. After selecting the
proper height, slide the backrest uphol-
stery back on with the overlap portion
unattached. Secure VELCRO®-style mate-
rial on backrest.
W A R N I N G S
!
L
The farther forward the axles are posi-
tioned, the m ore likely it is that the wheel-
chair will tip over backward.
Always adjust the wheel locks after m aking
any change to the cam ber tube position, so
the wheel locks em bed into the tires to
prevent wheel m ovem ent when in the
locked position.
2. W heel Cam ber
G. BACK A N GLE A DJUSTMEN T
(Fo ld in g b a ck r e st )
Wheel camber is determined by the cam-
o
o
o
ber tube. Tubes are available in 0 , 3 , 6 ,
o
o
o
An 6o angle adjustment is standard. Angle
adjustment is made by moving the posi-
tion of the backrest support bracket. The
adjustment on each side of the chair must
be exactly equal. Loosen the lock nut and
adjust to the desired angle and retighten
lock nut. Check operation of backrest
after adjusting the angle.
9 , 12 and 15 angles.
A
3. W heelbase W idth Adjustm ent
Adjust the wheelbase width by loosening
the nuts and repositioning the axle sleeve
(A); retighten nut. Both sides should be
adjusted the same.
W A R N I N G S
!
L
Always adjust the wheel locks after m aking
any change to the cam ber tube position, so
the wheel locks em bed into the tires to
prevent wheel m ovem ent when in the
locked position.
24
25
I X
.
S E T U P
&
A D J U S T M E N
T
I X
.
S E T U P
&
A D J U S T M E N
T
J. FOOTREST
I. WH EEL LOCKS
Adjust height by removing bolts and sliding
footrest up or down to desired position.
Replace bolts.
Note: Use a torque setting of 100 in.-lbs. when
setting up wheel locks.
1. Low-Mount Scissor W heel Locks:
Loosen screws on top clamp. Slide
assembly toward rear wheel until clamp
embeds into tire to prevent wheel move-
ment, when in locked position. Adjust
angle position and tighten screws.
Note: Footrest adjusts in 3/4” increments. Keep
footrest 1”-2” above the ground. Use a torque set-
ting of 100 in./lbs. when adjusting footplate.
K. A N TI-TIP TUBES (Op t io n a l)
Note: Use a torque setting of 100 in.-lbs. when set-
ting up the anti-tip tubes.
W A R N I N G S
!
L
Using wheel locks for braking is danger-
ous. Use wheel locks for parking O NLY.
W hen properly adjusted, wheel locks pre-
vent the rear wheels from turning when
the chair is parked. Always adjust the
wheel locks after m aking any changes to
the rear axle sleeve position. W heel locks
should be em bedded into the tires to pre-
vent wheel m ovem ent.
Remove anti-tip tubes from anti-tip
receivers. Remove button head bolts from
camber tube mounting brackets. Install
anti-tip receiver on the underside of the
camber tube with the long part of the tube
facing rearward. Use the longer screw
supplied with the anti-tips and reinstall
the camber tube and mounting brackets.
Insert the anti-tip tube into the receiver.
Turn the anti-tip tube down until release
pin is through the receiver mounting hole.
Insert second anti-tip tube the same way.
2. High-Mount Push-to-Lock or Pull-to-
Lock W heel Locks:
To adjust push-to-lock toggle type locks that
mount with a split clamp, loosen the screws
on the top of each clamp. Using a 3/16”
Allen wrench, turn one of the screws coun-
terclockwise one-quarter turn. Repeat the
same process with the second of the two
screws. Alternately loosen the screws (two
turns each) until both screws are removed.
Slide clamp toward the rear wheel until the
wheel lock is embedded into the tire to
prevent wheel movement (when in the
locked position). Tighten screws. Some
adjustments to the wheel lock position can
be accomplished without moving the clamp.
To adjust, loosen the two socket-head cap
screws on the top of the clamp. Slide the
mounting bar forward or backward and
rotate it to the correct angle position. The
wheel lock should embed into the tire to
prevent wheel movement when in the
locked position. Tighten screws.
CAUTION:To allow the anti-tip tubes to func-
tion properly there must be a 1 1/2” to 2”
clearance from the anti-tip wheel to the
ground. To maintain this clearance an adjust-
ment in the positioning of the anti-tip tube
should be made to correspond with any
change in seat height.
W A R N I N G S
!
L
Failure to adjust anti-tip tubes correctly can
result in injury to the rider. Anti-tip tubes
are available from your local authorized
Q uickie supplier. Q uickie Designs recom -
m ends anti-tip tubes for wheelchairs.
Note: High-mount push-to-lock require frame
modifications for use on your Shadow Rigid.
26
27
X
.
T R O U B L E S H O O T I N
G
X
I . M A I N T E N A N C E
You will need to adjust your chair from time to time for best performance (espe-
cially if you alter the original settings). This chart gives you a first solution, then a
second and a third if needed. You may need to look farther to find the best solu-
tion for a specific problem.
A . IN TRODUCTION
1. Proper maintenance will improve performance and extend the useful life
of your chair.
2. Clean your chair regularly. This will help you find loose or worn parts and
make your chair easier to use.
Note: To keep track of your progress, make only ONE change at a time.
3. Repair or replace loose, worn, bent or damaged parts before using this
chair.
4. To protect your investment, have all major maintenance and repair work
done by your authorized Quickie supplier.
W A R N I N G S !
!
L
If you fail to heed these warnings your chair m ay fail and cause severe
injury to the rider or others.
1. Inspect and m aintain this chair strictly per chart.
2. If you detect a problem , m ake sure to service or repair the chair
before use.
3. At least once a year, have a com plete inspection, safety check and
service of your chair m ade by an authorized Q uickie supplier.
B. MA IN TEN A N CE CH A RT
28
29
X
I . M A I N T E N A N C E
X
I I . Q U I C K I E L I M I T E D W A R R A N T Y
A . FOR LIFETIME
C. MA IN TEN A N CE TIPS
Quickie warrants the frame and quick-release axles of this wheelchair against
defects in materials and workmanship for the life of the original purchaser.
The expected life of this frame is five years.
1. Axles & Axle Sleeves:
Check axles and axle sleeves every six months to make sure they are tight.
Loose sleeves will damage the axle plate and will affect performance.
2. Tire Air Pressure:
B. FOR TWO (2 ) YEA RS
Check air pressure in pneumatic tires at least ONCE A WEEK. The wheel
locks will not grip properly if you fail to maintain the air pressure shown on
tire sidewall.
We warrant all Quickie-made parts and components of this wheelchair against
defects in materials and workmanship for two years from the date of first
consumer purchase.
D. CLEA N IN G
1. Paint Finish
C. LIMITATION S
1. We do not warrant:
a. Clean the paint finish with mild soap at least once a month.
b. Protect the paint with a coat of non-abrasive auto wax every three
months.
• Tires and tubes, upholstery, armrests and push-handle grips.
• Damage from neglect, misuse, or from improper installation or repair.
• Damage from exceeding weight limit of 250 pounds.
2. This warranty is VOID if the original chair serial number tag is removed
or altered.
2. Axles and Moving Parts
a. Clean around axles and moving parts WEEKLY with a slightly damp (not
wet) cloth.
3. This warranty applies in the USA only. Check with your Quickie supplier
to find out if international warranties apply.
b. Wipe off or blow away any fluff, dust, or dirt on axles or moving parts.
Note: You do not need to grease or oil the chair.
D. WH AT WE WILL DO
3. Upholstery
1. Our sole liability is to repair or replace covered parts.This is the exclu-
sive remedy for consequential damages.
a. Hand-wash (machine washing may damage fabric).
b. Drip-dry only. DO NOT machine dry as heat will damage fabric.
E. WH AT YOU MUST DO
E. STORAGE TIPS
1. Obtain from us, while this warranty is in effect, prior approval for return
or repair of covered parts.
1. Store your chair in a clean, dry area. If you fail to do so, parts may rust
or corrode.
2. Return the wheelchair or part(s), freight pre-paid, to Quickie at: 2842
Business Park Avenue, Fresno, CA 93727-1328.
3. Pay the cost of labor to repair, remove or install parts.
2. Before using your chair, make sure it is in proper working order. Inspect
and service all items on the "Maintenance Chart." (See p. 27)
3. If stored for more than three months, have your chair inspected by an
authorized Quickie supplier before use.
F. N OTICE TO CON SUMER
1. If allowed by law, this warranty is in place of any other warranty (written
or oral, express or implied, including a warranty of merchantability, or
fitness for a particular purpose).
2. This warranty gives you certain legal rights.You may also have other rights
that vary from state to state.
Record your serial number here for future reference:
________________________
30
31
Sunrise Hom e Healthcare Group
Mobility Products Division
7477 East Dry Creek Parkway • Longmont, Colorado • 80503 USA
(303) 218-4500 or (800) 456-8165
in Canada (800) 263-3390
© 1997, Sunrise Medical 12.97
931142 Rev. B
|