Philips Universal Remote T374AH User Manual

T374AH REMOTE CONTROL INSTRUCTIONS  
Channel Guide  
The T374AH remote control is used to perform setup  
and verification operations on Philips Consumer  
Electronics Company commercial chassis. This remote  
is fully backward compatible with previous commercial  
chassis setup remotes, but has added functionality.  
The three buttons at the bottom of the remote,  
TV Guest,  
TV Setup, and  
DCM Setup,  
are called function buttons. They are used to select  
the desired function to be performed.  
This feature is activated with the Guest or Setup  
remotes CH GDE button. This feature uses the labels  
that are assigned by the channel labeling function  
described on page three. Once activated by pressing  
the CH GDE button, the TV lists the Channel Labels  
for channels with assigned labels. Channels that are  
not in the Favorite Station memory (see “ADD  
CHANNEL” on page four) will not be displayed. Each  
listing or “page” will show seven channel labels. Each  
press of the CH GDE button will show subsequent  
channel listing pages if they exist. The maximum num-  
ber of labels that can be displayed is 32. If CH GDE is  
not pressed for seven seconds, the listing will timeout.  
If any other remote command is sent that requires the  
television on-screen display, the listing will be cleared,  
and that command invoked.  
SLEEP  
RECALL  
SLEEP  
RECALL  
-
+
-
+
M
M
A/ CH  
A/ CH  
VOL  
VOL  
CH  
CH  
MUTE  
MUTE  
A
B
E
C
D
G
A
B
E
C
D
G
F
F
ENTER  
ENTER  
TV Guest m ode will emulate the “Guest” remote  
commands. This provides the installer the ability to  
verify proper “Guest Remote” operation using only  
one remote. Only the commands supported on the  
“Guest” remote may be valid. To use this function,  
press the TV GUEST button, then press any button  
that corresponds to the “Guest Remote.” The remote  
will remain in the TV Guest mode until another func-  
tion button is pressed.  
P.PREF  
1
4
3
6
P.PREF  
1
4
3
6
2
5
2
5
CC  
CC  
8
0
9
7
8
0
9
7
CH GDE  
POWER  
CH GDE  
POWER  
TV  
TV  
DCM  
TV  
TV  
DCM  
GUEST SETUP SETUP  
GUEST SETUP SETUP  
IMPO RTANT: When programming is  
complete, press or depress the RECALL  
button to save the program changes in the  
TV memory.  
TV Setup m ode is used to set all the TV control settings and commercial features.  
This function is completely backward compatible with previous setup transmitters but  
has additional buttons that are valid for newer TV control systems. The remote will  
remain in the TV Setup mode until another function button is pressed.  
To adjust the TV for either Hotel or Consumer mode,  
press the TV SETUP button on the remote, then enter  
the numerical sequence 02 49 95, then press the  
SELECT button. Choose between Hotel or Consumer  
mode by pressing either the + or - button. Only a lim-  
ited amount of features are available in Consumer  
mode.  
DCM Setup (Data Com m unication Module) m ode is similar to the TV Guest  
Mode except the Select and Cursor keys send “Softkey” commands, allowing the DCM  
to have its own setup keys. The function of these keys will depend upon each DCM  
manufacturer. The remote will remain in the DCM Setup mode until another function  
button is pressed.  
Softkey is defined as a command that is never acted upon by the TV control system.  
It is always passed through the “Smart Port” to the DCM. Each DCM manufacturer  
can make its own interpretation of the function of the key. The functional description  
of the TV controls and features are as follows: To set up the TV, press the TV Setup  
button to place the remote in TV Setup mode.  
4
1
IB7166E002  
MAC 6009  
 

Petsafe Pet Care Product PAC00 12893 User Manual
Philips Cell Phone 32PFL9632D User Manual
Philips Flat Panel Television PT 5606 User Manual
Philips Indoor Furnishings 30187 31 16 User Manual
Philips Mouse SPM1500 User Manual
Philips TV Cables SWA2530 User Manual
Plantronics Headphones DA45 User Manual
Polaroid Digital Camera PDC 505 User Manual
Polycom Server 1725 36028 001 User Manual
Polycom Telephone IP300 User Manual