PYLE Audio GPS Receiver PLNVB26 User Manual

PLNVB26  
OWNER’S MANUAL  
Mobile Video System  
 
SAFETY INSTRUCTIONS  
• Arrange cables so that no-one can tread on them or trip over them. Do not place  
any items on the cable.  
Working with memory card  
This navigation system supports SD memory cards.  
1)Inserting memory cards:  
Carefully take the memory card out of its packing (if included). Take care not to  
touch or dirty the contacts. Push the memory card carefully into the card slot. The  
side of the memory card wearing the label must point upwards. The memory card  
should slightly lock in place.  
2)Removing memory cards  
Do not remove the memory card while it is accessed. This could result in loss of  
data.  
To remove the card press lightly onto the upper edge until it ejects.  
Pull the card out without touching the contacts.  
Store the memory card in the packing or in another safe location. Memory cards are  
very fragile.  
Take care not to dirty the contacts and not to force the card.  
3)Accessing Memory Cards  
The appliance only supports memory cards in the FAT16/32 file format.  
• Data Exchange VIA Card Reader  
You need a SD card reader to transfer or install map and software data. Insert the  
card into SD card reader and copy the data directly to the card.  
• Resetting The Navigation System  
This option restarts the navigation system without erasing the data installed. This  
kind of reset is often used to reorganize the memory. After reset, all running programs  
are interrupted and the working memory is reinitialized. Choose this option if your  
navigation system is not responding or working properly.  
Press reset button (4) will restart the navigation system.  
• Tips for Navigation  
1)Do not manipulate the navigation system while driving to protect yourself and  
others from accidents!  
2) Only look at the display (not included in the package) when you are in a safe  
driving situation!  
3) Attention: The road layout and driving rules take precedence over the instructions  
of the navigation system. Only follow the instructions when circumstances and  
driving rules permit it!  
4) The direction statements of the navigation system given do not release the driver  
of the vehicle from his or her duty of care or personal responsibility.  
5) Plan routes before you leave. If you want to play a new route whilst on the road  
stop driving.  
6) In order to receive the GPS signal correctly, metal objects may not hinder reception.  
Attach the GPS antenna onto the inside of the windscreen or near the windscreen.  
Try different positions in your vehicle in order to find the best reception  
Notes for Use In A Vehicle  
Take care that the cable does not impede any safety components. Do not mount  
the components within the operating range of any airbags. Check all safety equipment  
in your car after installation.  
3
 
INSTALLATION  
• Mounting The Navigation Set In A Car  
Use 4 screws ( 5X25) to install the navigation set to the car, please refer to the  
followed diagram.  
4
 
ACCESSORIES  
• GPS BOX  
• REMOTE CONTROL  
• GPS ANTENNA  
• REMOTE SENSOR  
• RGB TO RGB CABLE  
• RGB TO RCA VIDEO LINEOUT  
• SD CARD  
• SCREW 5X25 (4 PCS)  
5
 
GPS BOX  
One Side  
1
2
Other Side  
3
4
5
6
1. GPS ANT (GPS Antenna, To receive GPS signal.)  
2. Socket (Connect GPS Box And The Unit)  
3. RGB/VIDEO Switch (Switch between RGB mode and VIDEO mode.)  
4. RESET (Reset Button)  
5. PWR (Power Indicator LED)  
6. SD (SD Card Interface)  
6
 
REMOTE CONTROL  
9
8
1
2
3
7
6
5
4
1. ESC  
Press it to exit the current menu.  
Press it to enter the selected item.  
2.  
3.  
(ENTER)  
/
,
/
These buttons serves as navigation-pad, moves up / down / left /  
right by pushing the corresponding area of the pad.  
4. VOL+/-  
5.  
Press VOL+/- buttons to increase/decrease the sound.  
Zoom out button.  
6.  
Zoom in button.  
7. Control  
Press it to enter control interface.  
8. (MENU)  
9. POWER  
Press it to enter the navigation menu.  
Press it to turn the GPS box on or off.  
7
 
ELECTRICAL CONNECTION  
Wiring (1)  
GPS BOX  
EXTERAL  
ANTTENA  
20 PIN  
Wiring (2)  
GPS BOX  
EXTERAL  
ANTTENA  
(WHITE)  
R (RED)  
AUDIO L OUT  
AUDIO R OUT  
VIDEO OUT  
RGB OUT  
G (GREEN)  
RCA OUT  
(RED)  
B (BLUE)  
SYNC  
(BROWN)  
(YELLOW)  
B+ (YELLOW)  
ACC (RED)  
REMOTE SENSOR  
CONNECTOR (BLACK)  
GROUND (BLACK)  
(OPTIONAL)  
EXTERNAL REMOTE SENSOR  
(OPTIONAL)  
(OPTIONAL)  
8
 
OPERATION  
• Console  
confirm the screen adjustment.  
When all the connections is finished,  
turn the unit on, switch the mode to  
navigation mode, the unit will enter the  
following interface automatically.  
2) Tap to enter screen calibration mode,  
and you can see a plus displayed on  
screen. Tap the plus firmly, the plus will  
continue to move until the screen is  
aligned. And “OK” will appear on  
screen, tap OK will exit screen  
calibration mode.  
Note: If you have set “Auto navigation  
when power on”, when you turn on the  
unit, it will skip Console interface and  
enter navigation interface automatically.  
3) Tap  
to enter GPS Monitor interface,  
to enter Navi Option interface.  
it is for factory testing.  
Tap Agree, the following interface will  
appear, tap Quit will return to Console  
interface.  
4) Tap  
• Setting  
Tap  
Tap check box  
to enable “Auto  
icon on Console interface to  
run navigation when power on”. When  
you select “Auto run navigation when  
power on”, every time when you turn  
the unit on, it will enter navigation mode  
automatically.  
enter Setting interface like followed:  
5) Tap  
to enter Language Option  
menu. You can select system language  
in this menu.  
1) Use remote control to select  
icon  
and enter screen adjust mode, you can  
see the following interface displayed  
on screen. Use remote control to move  
the screen up/down, left/ right. Then  
press OK button on remote control to  
9
 
OPERATION  
6)Tap  
to enter volume option menu.  
Use the remote control or tap  
to see following two navigation  
interface:  
icon  
There are two method to adjust the  
volume: Method A: When you select  
or  
, press OK button on remote  
control to adjust the system volume  
level. Method B: When you select  
,
press / (Left/Right) buttons on remote  
control to adjust the volume up or down.  
Tap chock box  
to mute the  
Tap  
to enter destinations menu:  
sound. Tap  
to select keyclick and  
screenclick volume type among: None,  
Softness or Generosity. When finishing  
volume setup, tap  
exit current menu.  
to save and  
7) Tap  
to enter system info interface.  
The following information will be  
displayed in this interface: SN (Serial  
No.), Hardware Version, Software  
Version, Total Memory and Available  
Memory.  
Now you can navigate to anywhere you  
want just following the instruction on  
the navigation interface.  
How to use the navigation software,  
please refer to the navigation software  
instruction manual.  
Note: In the video mode, you must  
select video output signal to the monitor.  
And In RGB mode, you must select  
RGB output to the monitor.  
• Navigation  
When you connect a GPS box to DVD  
unit, turn GPS box on then switch the  
DVD unit mode to navigation mode,  
you will enter the control interface like  
followed:  
10  
 
SOFTWARE OPERATION  
1) When all the connections is finished,  
turn the unit on, switch the mode to  
navigation mode, the unit will enter the  
following interface automatically.  
Tap  
icon to enter Device interface,  
then select StorageCard folder.  
Note: If you have set “Auto navigation  
when power on”, when you turn on the  
unit, it will skip Console interface and  
enter navigation interface automatically.  
Double tap the StorageCard folder to  
open it and select NaInstall.exe file.  
Tap Agree, the following interface will  
appear, tap Quit will return to Console  
interface.  
2) Tap  
icon to enter Setting interface  
like followed:  
Exit this menu and return to Console  
interface.  
4) Tap  
icon the navigation software  
will be installed automatically, and you  
can see the followed interface:  
3) Tap  
will enter Navi Option menu:  
11  
 
SOFTWARE OPERATION  
When the installation is finished it will  
return to Console interface automatically.  
5) Tap icon to enter Setting menu, then  
tap  
in Setting menu to enter Navi  
Option menu:  
Tap  
to enter Device menu:  
Double tap NANDFlash folder to open  
it :  
Double tap Destinator folder to enter it  
and select Dextinator.exe, then tap  
to exit current menu.  
6) Return to Console interface, Tap  
icon will enter navigation Interface.  
12  
 
8800-0G9013-  
 

Pentair Swimming Pool Vacuum Jet Vac User Manual
Philips Cassette Player AQ 5040 20M User Manual
Philips Cassette Player AQ5130 User Manual
Philips Projector PT F100NTE User Manual
Pitco Frialator Fryer E400 User Manual
Poulan Lawn Mower PR17H42STF User Manual
Poulan Snow Blower 199350 User Manual
Poulan Snow Blower 428701 User Manual
Poulan Trimmer 545186897 User Manual
Professional Series Refrigerator PS72001 User Manual